SNMP 4E1 to 4 Eth converter
Ethernet over 4E1 Converter (4E1 to Ethernet cinverter)
allows the user to send Ethernet data, between two points, over E1
links. E1 Interfaces are 120 Ohms (75 Ohms is optional). Ethernet
Interface options may be ordered as 10/100 Base-T Electrical
Ethernet or 100Base-FX Optical Ethernet over 850nm/1310nm/1550nm
single mode optical fiber interfaces.
The equipment be always installed and used in pairs, with one
terminal being installed at either end of the E1 link.
.
Specification
Provides 4 E1 interfaces
Provides 4 Ethernet 10/100Mbps (Elecrical) ports for each converter
The maximum transmission rate of Ethernet data over E1 links is
8.192Mbit/s
Optionally provides 3 Ethernet 10/100Mbps (Elecrical) ports and 1
Ethernet (Optical) port for each converter
E1 supports three working modes of transmission. Un-Framed/Transparent,
Framed, CAS / PCM 30 format Supports VCAT (virtual concatenation) and
LCAS (link capacity adjustment scheme) protocol, and complies with ITU-T
G.7042 specifications
Mapping to E1 complies with ITU-T G.7043 and G.8040 specifications
Supports differential delay of up to 120ms on E1 links
Complies with IEEE 802.3 specifications
Support VLAN tagging as per 802.1Q
Supports X.86, LAPS and HDLC transmission protocols
Supports 100M full-duplex mode
Configurable frame length upto 1916 bytes (MTU size)
Supports GFP-F encapsulation complying with ITU-T G.7041
Provide smooth adjustment of bandwidth
Provides Loss of Frame alarms
Provides error frame statistic
Supports automatic removal and addition of E1 links
Available with MAC address list filtration, learning, and updating
functions
A large external SDRAM buffering for handling data bursts
E1 Interfaces support errors count
Tolerant for drift of E1 signal of up to 512UI.
Error code correction and automatic protection and recovery of E1
channel.
Network management function. The main function of network management
system is to fulfill the inquiry for local and remote devices and
configuration management including inquiry of alarm status on E1 line,
Ethernet working status, and loopback control etc.
Automatic ethernet negotiation function. Supports 10M/100M and working
modes of both full-duplex and semi-duplex.
Transparently transmits ultra-long frames stipulated in IEEE 802.1Q, and
supports Ethernet switches with VLAN function.
Supports two synchronization clock modes, Internal Clock and Network
Clock (Loop-Timed Clock)
Imbedded, dynamic Ethernet MAC address list (5000 addresses), and filter
function for local data frames
Specifications
Electrical Ethernet Interface:
Connector: RJ-45
Working mode: Auto - negotiation is the default setting
Complies with IEEE 802.3 and 10/100 Base-Tx Ethernet Protocol
E1 interface
Bit rate:2.048Mb/s±50ppm
Code format: HDB3
Impedance: 75 Ohm is default, Optional 120 Ohm
Jitter transfer, Jitter tolerance comply with ITU-T G.703、G.704、G.823
recommendations
Ethernet related parameters
MAC address table capacity: 1024
MAC aging time: 5 min
Minimum frame-length: 64 bytes
Maximum frame-length: 1916 bytes
Working mode: Support auto-negotiation compliant to IEEE802.3u. Enabled
as default
VLAN function: Disabled as default, you can set VLAN's from GUI
Flow control: Enabled as default
Bandwidth: ≈n×E1（n=0～4）Default is 4 ×E1 ≈8Mbps
Physical:
Dimension: 434mm×44mm×155mm（width× height× depth）
Power consumption: 8W±10％
Ordering options for power supply are DC 48, or AC 96 - 260 universal
with all kind of power plugs. Double power supply on request.
Operating temperature: -5℃～65℃
Storage temperature: -40℃～70℃
Humidity: ≤95％，free from condensing
Typical Application:
Bridging Ethernet LANs over existing TDM (E1) telecom network.
Extending Ethernet networks utilizing TDM (E1) landline based telecom
infrastructure.
Interconnecting DSLAMs to Central Routers over PDH/SDH
Interconnecting IP based GSM base stations
Interconnecting WiMAX base stations
Using telecom network of E1s / PDH / SDH microwave etc. carrying E1s to
transport Ethernet data.
In all cases the equipment be always installed and used in pairs, with
one terminal being installed at either end of the network
Solutions
.
Model
HYC-
Download